Arm (Shoulder, Elbow, Forearm)

Print
C08-Central_rotator_bracket
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib2
Number of this part for two arm Pib4
Mass – (Mass with supports)20g
Printing time52min
Suggested orientation
After printing processingNone

C09-Central_rotator_connector
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Number of this part for one arm Pib2
Number of this part for two arm Pib
4
Mass – (Mass with supports)32g
Printing time1h 10min
Suggested orientation
After printing processingClean supports

C10-Elbow
Suggested layer height0.2mm
Suggested infill percentage75%-85%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)197g
Printing time7h
Suggested orientation
After printing processingClean supports

C11-Elbow_servo_scaffold
Suggested layer height0.2mm
Suggested infill percentage65%-75%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)61g
Printing time2h 40min
Suggested orientation
After printing processingNone

C12-Elbow_motor_connector
Suggested layer height0.2mm
Suggested infill percentage50%-60%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)6.5
Printing time18min
Suggested orientation
After printing processingNone

C13-Elbow_shell_lower
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)95g
Printing time4h
Suggested orientation
After printing processingNone

C15-Central_rotator_motor_connector
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib2
Number of this part for two arm Pib4
Mass – (Mass with supports)16.5g
Printing time35min
Suggested orientation
After printing processingNone

C19-Forearm_distal_top
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)148g
Printing time5h
Suggested orientation
After printing processingNone

C20-Forearm_cover
Suggested layer height0.2mm
Suggested infill percentage25%-35%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)12g
Printing time1h
Suggested orientation
After printing processingNone

C21-Elbow_servo_holder
Suggested layer height0.2mm
Suggested infill percentage50%-60%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)36g
Printing time1h 45min
Suggested orientation
After printing processingNone

C24-Forearm_tube_enclosure
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0.56g
Printing time4min
Suggested orientation
After printing processingNone

C50-Wrist_Joint_Connector
Suggested layer height0.2mm
Suggested infill percentage100%
Supports
Number of this part for one arm Pib2
Number of this part for two arm Pib4
Mass – (Mass with supports)1.4g
Printing time12min
Suggested orientation
After printing processingNone
C260-Flange_Inner_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)8.5g
Printing time21min
Suggested orientation
After printing processingNone
C24-Forearm_tube_enclosure
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0.56g
Printing time4min
Suggested orientation
After printing processingNone

C61-Motor_bracket_inner_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0148g
Printing time4h 20min
Suggested orientation
After printing processingNone
C24-Forearm_tube_enclosure
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0.56g
Printing time4min
Suggested orientation
After printing processingNone

C62-Ringflange_Inner_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)33g
Printing time1h
Suggested orientation
After printing processingNone
C24-Forearm_tube_enclosure
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0.56g
Printing time4min
Suggested orientation
After printing processingNone
C24-Forearm_tube_enclosure
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0.56g
Printing time4min
Suggested orientation
After printing processingNone

C63-Motor_Axis_Inner_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)52g
Printing time1h 40min
Suggested orientation
After printing processingNone

C64-Motor_Axis_Cap_Inner_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)22g
Printing time45min
Suggested orientation
After printing processingNone

C65-Bracket_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)176g
Printing time6h
Suggested orientation
After printing processingNone
C24-Forearm_tube_enclosure
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0.56g
Printing time4min
Suggested orientation
After printing processingNone

C66-Cap_Front_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)45g
Printing time1h 24min
Suggested orientation
After printing processingNone

C67-Cap_Back_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)27g
Printing time50min
Suggested orientation
After printing processingNone

C68-Inner_Ring_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib2
Number of this part for two arm Pib4
Mass – (Mass with supports)11g
Printing time27min
Suggested orientation
After printing processingNone
C69-Inner_Ring_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)320g
Printing time9h 20min
Suggested orientation
After printing processingNone
C70-Shell_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)109g
Printing time3h 40min
Suggested orientation
After printing processingNone
C72-Plate_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)0.9g
Printing time4min
Suggested orientation
After printing processingNone
C73-Motor_Bracket_Outer_Shoulder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)14g
Printing time36min
Suggested orientation
After printing processingNone
C74-Wire_holder
Suggested layer height0.2mm
Suggested infill percentage40%-50%
Supports
Number of this part for one arm Pib1
Number of this part for two arm Pib2
Mass – (Mass with supports)4g
Printing time19min
Suggested orientation
After printing processingNone

pib is a product of isento GmbH
Ostendstraße 242, D-90482 Nürnberg

Imprint
Privacy Policy

About Us | Our Vision

We believe that humanoid robots will bring about the next big changes in our society and that they will support us in our daily lives.

Creating these robots is a huge task that should not be placed in individual hands. That is why pib is open and offers anyone interested the chance to shape our future together.

You are currently viewing a placeholder content from Default. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.

Unblock content
More Information
Copyright © 2022 isento GmbH
Go to Top