Neck

Default pro neck

A50-Neck_housing
Latest version downloadpib-stls/A-Head/A50-Neck_housing.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A50-Neck_housing.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)100g
Suggested orientation
After printing processingNone
A51-Bearing_holder_Neck
Latest version downloadpib-stls/A-Head/A51-Bearing_holder_Neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A51-Bearing_holder_Neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)9g
Suggested orientation
After printing processingNone
A52-Motor_bracket_neck
Latest version downloadpib-stls/A-Head/A52-Motor_bracket_neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A52-Motor_bracket_neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)18g
Suggested orientation
After printing processingNone
A53-Vertical_shaft_neck
Latest version downloadpib-stls/A-Head/A53-Vertical_shaft_neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A53-Vertical_shaft_neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)5.5g
Suggested orientation
After printing processingNone
A54-Vertical_Motor_Connector_neck
Latest version downloadpib-stls/A-Head/A54-Vertical_Motor_Connector_neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A54-Vertical_Motor_Connector_neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)3.4g
Suggested orientation
After printing processingNone
A55-Cap_neck
Latest version downloadpib-stls/A-Head/A55-Cap_neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A55-Cap_neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)15.8g
Suggested orientation
After printing processingNone
A56-Top_part
Latest version downloadpib-stls/A-Head/A56-Top_part.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A56-Top_part.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsFor support enforcers only – paint on support

Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)53g
Suggested orientation
After printing processingNone
A57-Horizontal_motor_connector_neck
Latest version downloadpib-stls/A-Head/A57-Horizontal_motor_connector_neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A57-Horizontal_motor_connector_neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)3.5g
Suggested orientation
After printing processingNone
A58-Horizontal_shaft_neck
Latest version downloadpib-stls/A-Head/A58-Horizontal_shaft_neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A58-Horizontal_shaft_neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)4.5g
Suggested orientation
After printing processingNone
A59-L-Side_arm_neck_left.
Latest version downloadpib-stls/A-Head/A59-L-Side_arm_neck_left.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A59-L-Side_arm_neck_left.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)30g
Suggested orientation
After printing processingNone
A59-R-Side_arm_neck_right
Latest version downloadpib-stls/A-Head/A59-R-Side_arm_neck_right.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A59-R-Side_arm_neck_right.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)30g
Suggested orientation
After printing processingNone
A60-Horizontal_shaft_short_neck
Latest version downloadpib-stls/A-Head/A60-Horizontal_shaft_short_neck.stl at main · pib-rocks/pib-stls · GitHub
Stable release downloadpib-stls/A-Head/A60-Horizontal_shaft_short_neck.stl at main · pib-rocks/pib-stls · GitHub
Suggested layer height0.25mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Mass – (Mass with supports)2.2g
Suggested orientation
After printing processingNone

Advanced neck

A05-Neck_base
Latest version downloadpib-stls/A-Head/A05-Neck_base.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.3 mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Suggested orientation
After printing processingNone
A06-Neck_base_connector
Latest version downloadpib-stls/A-Head/A06-Neck_base_connector.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.2 mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib3
Number of this part for two arm Pib3
Suggested orientation
After printing processingNone
A07-Neck_servo_connector
Latest version downloadpib-stls/A-Head/A07-Neck_servo_connector.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.2 mm
Suggested infill percentage30%-40%
SupportsNone
Number of this part for one arm Pib3
Number of this part for two arm Pib3
Suggested orientation
After printing processingNone
A08-Neck_arm
Latest version downloadpib-stls/A-Head/A08-Neck_arm.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.3 mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib3
Number of this part for two arm Pib3
Suggested orientation
After printing processingNone
A09-Neck_head
Latest version downloadpib-stls/A-Head/A09-Neck_head.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.3 mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Suggested orientation
After printing processingNone
A10-Neck_head_connector
Latest version downloadpib-stls/A-Head/A10-Neck_head_connector.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.2 mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib3
Number of this part for two arm Pib3
Suggested orientation
After printing processingNone
A12-Neck_driving_bevel_gear
Latest version downloadpib-stls/A-Head/A12-Neck_driving_bevel_gear.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.2 mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib3
Number of this part for two arm Pib3
Suggested orientation
After printing processingNone
A13-Neck_driven_bevel_gear
Latest version downloadpib-stls/A-Head/A13-Neck_driven_bevel_gear.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.2 mm
Suggested infill percentage30%-40%
SupportsSupports on build plate only
Number of this part for one arm Pib3
Number of this part for two arm Pib3
Suggested orientation
After printing processingClean supports
A14-Neck_ballbearing_holder
Latest version downloadpib-stls/A-Head/A14-Neck_ballbearing_holder.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.3 mm
Suggested infill percentage20%-30%
SupportsNone
Number of this part for one arm Pib1
Number of this part for two arm Pib1
Suggested orientation
After printing processingNone
A15-Neck_ballbearing_holder_leg
Latest version downloadpib-stls/A-Head/A15-Neck_ballbearing_holder_leg.stl at main · pib-rocks/pib-stls · GitHub
Stable release download
Suggested layer height0.2 mm
Suggested infill percentage20%-30%
SupportsSupports on build plate only
Number of this part for one arm Pib4
Number of this part for two arm Pib4
Suggested orientation
After printing processingNone
Go to Top